I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
product details:
nRF52840 custom board
nRFConnectSDK 2.2.0
we want to implement custom service interacting with the Android app.
Where we will receive on command from...
When creating a Bluetooth Mesh Vendor model ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols/bt/bt_mesh/vendor_model/dev_overview.html ) and if the vendor...
Hi there.
I'm using nRF5 SDK 17.1.0 with nrf52840.
I've configured my timer3 to interrupt by compare with 10us ticks. When it does, I toggle a pin. But when I measure...
Hello,
I am developing an app based on the the buttonless_dfu example and the secure bootloader and it works fine with Android.
I have the following problem with IOS:...
Hi all,
I have this annoying issue that I can't find a way to get rid of, and I don't know if it's intentional or if there is even a way to deactivate it.
I'm using VS...
Hi Community,
does someone here have experience with DAPLink?
currently the nRF5340 is still not spported by DAPLink, I`m considering to compile one. here is how to port...
Hi
We were using the nRF54L15 PDK V0.2.1. But after the update of the extension "nRF Connect for VS Code" to V2024.7.18 (pre-release), we are not able anymore to debug....
hi , i'm trying to connet sim800l and neo_6m modules to nrf52840dk using zephyr ,however i can't find any code source to use .,or do i have to creat the code from scratch...
Hello,
As I was using the sample“nrf_dm”(SDK v2.6.1),I wondered how programs were run, how threads were scheduled to give measurements, and how I could learn about this...
Hi, I'm working on nRF5340, NCS v2.6.1, Zephyr v3.4.99. The net core is running the child image HCI RPMsg controller. Th app core is running application and child image mcuboot...
Using the following code block nRF52833(PRX) can receive the data from PTX(nRF24L01+).
But how nRF52833 replies to nRF24L01+ with the ACK packet which includes user...
Hi, in order to reuse the original factory public Bluetooth MAC of nRF5340 based radio module, I had introduced a function that reads the MAC address out of UICR.OTP area...
After enabling Littlefs, I wanted to use a serial port to write files to it. I first tried using mcumgr, but currently encountered some problems. So, I tried to directly read...
Hi all,
I am using nrf SDK v2.5.2 and zephyr. In my application I want to measure a signal frequency coming from a GPIO, I read about the PPI and I thought it was good...