I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
Hi nordic support:
Our product used nRF52840 and nrf5_sdk_17.1.0. It's inconvenient to connect UART port when perform DTM test to testing nRF52840's RF performance. Could...
Hi there,
I hope this message finds you well!
I’ve been developing several products using Espressif’s modules that offer both Wi-Fi and BLE on a single SoC. I wanted to...
I'm developing a custom board that uses the nRF54H20.
The Getting Started guide for the nRF54H20DK explains how to use the pre-built BICR file and program it to the chip...
Hi Team, We are facing significant range issues on iPhones and other iOS devices with our hardware. We have tested these with both Custom App ( Made in House ) as well as...
Hi Nordic team,
I’m working on an nRF9151 DK with nRF Connect SDK v3.0.0. My goal is to send GNSS latitude/longitude data to a CoAP server.
The GNSS sample works fine...
Hello,
I have a series of nRF52840 devices that are already connected together in a Thread Network.
My system is composed by one client and multiple servers.
1) I'd...
Setup
Hardware: Nordic nRF7002DK as Wi-Fi STA (client) .
AP & Receiver: a Linux PC creates a Wi-Fi Hotspot/SoftAP (NetworkManager/hostapd) and simultaneously runs...
Hi,
I recently followed the instructions to install nRF Connect on Visual Studio by completing Exercise 1 of the nRF Connect SDK Fundamentals course: Exercise 1-1
I noticed...
I am trying to set CONFIG_TFM_BL2 and it seems like it cannot be set to 'y' because CONFIG_TFM_BL2_NOT_SUPPORTED is also set to 'y' in ${prj_name}/build/${prj_name}/zephyr...
I am using the nRF7002-DK to implement a BLE interface. I need to send packets > 23 bytes through a notification characteristic. I am currently using nRF Connect on an android...
Hello, I am using nrf52832 along with S132 soft device and SDK 17.1.0.
Can you please provide me the peer manager api that can list the paired/bonded devices? Also, is...
Hi,
I would like to ask a few things about Channel Sounding (CS):
Is there any recommendation which method (IFFT, PBR, RTT) should be used for reading the results...
Hi
I`m working with an nRF52833.
I've observed that when the module enters DFU mode, the Bluetooth advertising name seems to be limited to around 22 characters.
If I...
I am trying to run the WiFi Station sample, unchanged on a nrf7002DK, but receive the following error: "wifi_supplicant: Failed to add iface wlan0" Complete output as follows...
