Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
I am working on a project where we are sending data to a remote device as fast as possible. The sender will call bt_gatt_write() until it blocks the thread. So it is just...
Dear Sir/Madam ,
I am writing to request a review of the attached schematic. Please let me know if you have any questions, concerns, or suggested revisions.
If possible...
I am in process up migrating a legacy project from SDK v2.4 to v3.2 and going through each revision incrementally to catch all the changes needed to modernize it and maintain...
I have built and flashed both the exercise and the solution. However in both cases I am getting a connected and then disconnected ( Reason 42). I am clueless as to what is...
Hello.
I am currently testing nRF Cloud and encountering an issue. In the "Select a Project" menu, the "Create Project" button is disabled.
Here is some additional context...
I am using SDK 3.1.1. I am trying to use the "sensor get" command with the internal die temp sensor.
In theory, this is all off the shelf software. I didn't write anything...
While running scan & connection tests with NCS 3.2.1 , I encountered frequent connection timeouts ( bt_hci_core: Connection creation timeout triggered ) when using the Nordic...
I'm using the Power Profiler Kit II to measure current draw of an ESP32 board at idle. The PPK2 is connected to the battery terminals of the board (XIAO ESP32-S3) and whether...
Hello, I should like to enquire whether the nRF54L15-DK development board supports both Classic Bluetooth and Bluetooth Low Energy. Having reviewed the relevant documentation...
Dear All,
I'm following the nRF Connect SDK Fundamentals and I have a weird problem in the Lesson 3 exercise 2, section "Adding custom configurations".
The part with...
Hello everyone,
I've been testing the "central UART" with a "peripheral UART" (NUS) examples with two nRF54L15 DKs (nRF SDK v3.2.1 in VS Code). So far, everything is working...
Hello everyone!
I have a question regarding nRF9151 and the new DECT Hello sample. I have installed the newest version of the SDK, a preview of v3.3.0, built and flashed...
Hi!
NCS 3.1 On a custom board with nrf5340 and nrf7002, h ave successfully implemented and tested FOTA over Bluetooth Low Energy with Simultaneous updates for both cores...
Hi,
I'm trying to reduce the power consumption of my Matter Temperature sensor code.
I'm averaging around 90µA of consumption, but I'm confident that can be reduced. ...
