Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I have a custom nRF5340-based LE Audio broadcast sink built on nRF Connect SDK v3.2.0 (Zephyr 4.2.x). It scans for a broadcast source, establishes PA sync, creates a...
I am attempting to install and use the NRF Connect for vscode extension pack. I have made several attempts googling solutions posted by others facing similar issues. I am...
I am developing a BLE to LORA interface using nRF52840.
The LORA transceiver needs a 32MHz clock. Is there any way that I can get the nRF52840 to generate this?
I will...
In version 0.8 of the reference datasheet for the 54L15 (QFAA QFN-48), the capacitance value for C5 is specified as 10nF. Why was it updated to 2.2nF in version 0.9? What...
Hi!
I use nRF Cloud Lib of NCS v3.1.1. I couldn't find detailed info on how nrf_cloud_send() works with QoS > 0.
If I set QoS > 0 and get a 0 error code returned from...
Hello,
We are evaluating and developing a product using the latest nRF54L series controller and would like to know if IAR compiler support is available.
While Cortex-M33...
Due to resource exhaustion I'm curious whether this is possible.
It violates the 1-1 GPIOTE rule and I couldn't find any thread/message about it being possible or otherwise...
Hi,
Our customer needs to test the RF performance of nRF7000, please provide the test documents, test tools, and test procedures, as well as relevant information about WIFI...
i have small applications which can comfortably fit in as little as 32K of SRAM.... i have no issues with the mechanics of linking my program, as well as copying code from...
Hello,
I have a problem with my DK. Everytime I try to plug it in the USB C port of my Computer the J-Link OB is the only Chip that wakes up. I cant program the nrf5340...
Hi,
When using RTT for debugging on the nRF5340, after every flash i have to press the following button:
Then every time i get presented with the following dialog...
I would like to ensure that a particular GPIO pin is disconnected when an nRF52840 is powered up via the initial configuration specified in the DeviceTree board overlay file...
I get the following error when clicking flash button in nrfConnect VS Code extension with an nRF54L15 DK:
Error: One or more batch tasks failed: * 1057701224: Device error...
